tulip0:  MII transceiver #1 config 1000 status 782D advertising 01e1               
eth1: Digital DS21143 Tulip rev 65 at 0xf4008000, 00:10:83:F9:B4:32, IRQ 66.       
Uniform Multi-Platform E-IDE driver Revision 1.00alpha2                            
ide: Assuming 233MHz system bus speed for PIO modes; override with idebus=xx       
SiI680: IDE controler at PCI slot 0000:01:06.0                                     
SiI680: chipset revision 2                                                         
SiI680: BASE CLOCK == 1733                                                         
SiI680: 100% native mode on irq 128                                                
   ide0: MMIO-DMA at 0xf4800000-0xf4800007 -- Error, MMIO ports already in use.    
   ide1: MMIO-DMA at 0xf4800008-0xf480000f -- Error, MMIO ports already in use.    
hda: TS130220A1, ATA DISK drive                                                    
     < Your System ate a SPARK! Gah! >                                             
             \   ^__^                                                              
              \  (xx)\_______                                                      
                 (__)\       )\/\                                                  
                  u  ||----w |                                                     
                     ||     ||                                                     
swapper (pid1): Breakpoint (code 0)                                                
PSW: 00000000000001001111111100001111 Not tained                                   
r00-03  4d6f6f21 1032f010 10208f34 103fc2e0                                        
r04-07  103fc230 00000001 00000001 0000000f                                        
r08-11  103454f8 000f41fa 372d3980 103ee404                                        
r12-15  3ccbf700 10344801 103ee010 f0400004                                        
r16-19  f00008c4 f000017c f0000174 00000000                                        
r20-23  fed32840 fed32800 00000000 0000000a                                        
r24-27  0000ffa0 000000ff 103fc2e0 10326010                                        
r28-31  00000000 00061a80 4ff98340 10208f34                                        
sr0-3   00000000 00000000 00000000 00000000                                        
sr4-7   00000000 00000000 00000000 00000000                                        
IASQ: 00000000 00000000 IAOQ: 00000000 00000004                                    
 IIR: 00000000    ISR: 00000000  IOR: 00000000                                     
 CPU:        0   CR30: 4ff98000 CR31: 1037c000                                     
 ORIG_R28: 55555555                                                                
 IAOQ[0]: 0x0                                                                      
 IAOQ[1]: 0x4                                                                      
 RP(r2): probe_hwif+0x218/Ox44c                                                    
Kernel panic: Attenpted to kill init!                                              


A fatal exception 0E has occured at F0AD:42494C4C           
the current application will be terminated.                 
* Press any key to terminate the current application.       
* Press CTRL+ALT+DELETE again to restart your computer.     
  You will lose any unsaved information in all applications.
                 Press any key to continue                  

A problem has been detected and windows has been shut down to prevent damage
to your computer.


If this is the first time you've seen this Stop error screen,
restart your computer. If this screen appears again, follow
these steps:

Check to make sure any new hardware or software if properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.

If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use Safe Mode to remove or disable components, restart
your computer, presse F8 to select Advances Startup Options, and then select Safe Mode.

Technical information:

*** STOP: 0x000000FE (0x00000008,0x00000006,0x00000009,0x847075CC)

Collecting data for crash dump ...
Initializing disk for crash dump ...
Beginning dump of physical memory.
Dumping physical memory to disk:  65
panic(cpu 0): Unable to find driver for this platform: "PowerMac 3,5". 
backtrace: 0x0008c2f4 0x0002a7a0 0x001f0204 0x001d4e4c 0x001d4c5c 0x001a56cc 0x01d5dbc 0x001c62
1c 0x00037430 0x00037364 
No debugger configured - dumping debug information 
version string : Darwin Kernel Version 1.3: 
Thu Mar  1 06:65:40 PST 2001; root:xnu/xnu-123.5.obj~1/RELEASE_PPC 
DBAT0: 00000000 000000000 
DBAT1: 00000000 000000000 
DBAT2: 00001FFE 00000003A 
DBAT3: 00001FFE 00000003A 
backtrace: 0x0008c2f4 0x0002a7a0 0x001f0204 0x001d4e4c 0x001d4c5c 0x001a56cc 0x01d5dbc 0x001c62
1c 0x00037430 0x00037364 
panic: We are hanging here...